A woman pokes a PVC pipe into a planter, and 2 hours later, this fall porch idea is gorgeous!

For someone who has never really paid much attention to my own landscaping (because I’m too busy creating décor for inside), I feel like I’ve turned a new leaf this year. Maybe it’s because I just turned 30? Who knows! All I know is if I can keep the beautiful mums I got for this project alive this season, I’ll be doing something I never thought I’d do and I’ll be happy about it.

 

We want to help you DIY, so some of the materials in this post are linked to sellers. Just so you know, Hometalk may collect a small share of sales from the links on this page.

 

Time: 2 Hours Cost: $60 Difficulty: Medium

 

pumpkin topiary, crafts, gardening, halloween decorations
I’ve always envied homeowners whose homes look like they’re straight out of Southern Living magazine—their porches are prim and proper, their outdoor décor is on point, and I’ve even noticed “normal” topiaries adorning either side of their front door. I started seeing holiday topiaries so I figured now is a better time than any to try my hand at creating a topiary just for fall so here it goes!
SUPPLIES:

Plastic HOLLOW pumpkins (they’re 40% off right now at Michaels!)

¾”x10’ PVC pipe

Drill 

¾” paddle bit

Dremel (and/or box cutter—not pictured—I used both for this project)

Planter 

Not pictured:

Fairy lights

Potting soil

Chop saw

Pencil

Plants

 

pumpkin topiary, crafts, gardening, halloween decorations
STEP 1: Sketch, Carve and Design faces. You don’t have to do this first part of the step but unless you’re really good at using a drimmel or box cutter, I’d highly suggest it. I first took my pumpkins and drew a face on each one, using a pencil. I didn’t want scary jack-o-lanterns, but rather funny or cute ones which is why I chose a round nose on each pumpkin, droopy eyes and a smiley mouth.

ScaleAboutLOADING…


 

pumpkin topiary, crafts, gardening, halloween decorations
*NOTE: I HIGHLY RECOMMEND SAFETY GLASSES AND A MASK FOR THIS STEP IF YOU DECIDE TO USE A DREMEL AS DUST FLIES EVERYWHERE! Then, I took my dremel, and on the LOW setting, started shaving away the inside of the pumpkins’ faces. After a little while of doing this on one, I tried using a box cutter to cut out the faces instead—I found this to be much easier and less time consuming. So after switching to using the box cutter and once I had the faces cut out, I went back with the dremel to even out any rough spots and essentially clean up the cuts. If you’re not careful and don’t have a steady hand, your dremel will sort of ZING out of the lines without you really having any control of it—I did this a few times so to compensate, I covered my mistakes by accentuating them and making whimsical designs on my pumpkins. It’s funny because once all three of them were done and I stepped back to take a look at my work, I sort of saw Rob, me, and our son, Bo. Rob with the mustache/beard (the white one), me with random artsy designs (the orange one) and Bo with a laughing face and a tear (the black one…because he just turned 2 and he’s had his share of throw down tantrums but he’s really a happy kid—haha! Bless his heart!)

 

pumpkin topiary, crafts, gardening, halloween decorations
STEP 2: Measure for height of topiary. Next, I laid my carved pumpkins out, roughly how I thought they were going to stack on top of each other, and measured from the top to the bottom. I also stuck the 10’ PVC pipe in my planter to eyeball how high I thought I wanted my topiary to be, and lastly, I measured the depth of the planter. All-in-all I decided to cut my PVC at 42”. This would give me enough material to bury part of the pipe in the planter, plant mums around it and also be able to see the pumpkins clearly without being sunk too far down.

 

pumpkin topiary, crafts, gardening, halloween decorations
STEP 3: Cut PVC. After I got my measurement, I cut my PVC pipe at 42”. I made sure to do this as slow and steady as possible so that the saw didn’t tear up the plastic or rip the pipe out of my hand.

 

pumpkin topiary, crafts, gardening, halloween decorations
STEP 4: Drill holes in pumpkins for stacking. Finally, it was time to stack my pumpkins. I started with my bottom two pumpkins—stacked them one last time to see where they would connect—then drilled a hole in the bottom/center and on the top left side of my bottom pumpkin (black), using a paddle bit. I did the same for the bottom left and top right of my middle pumpkin (orange) and the bottom right of my top pumpkin (white). You can choose to drill a hole at the top of the top pumpkin if you’d like but mine sat nicely without falling over so I was good with just the bottom hole. I thought of possibly even putting a hat on top but in the end, I felt like the simple approach was best for my topiary. *Note: I chose the ¾” paddle bit since my PVC pipe was ¾”, however when I tried inserting the pipe into the holes of the pumpkins, the pipe was obviously the same size as the holes so I carefully went back through the holes with the same paddle bit to enlarge them slightly. I guess you could possibly go up a size in the paddle bit.

 

pumpkin topiary, crafts, gardening, halloween decorations
STEP 5: Prep planter. I know I’ll probably hear it from you guru gardeners out there, but being a complete brown-thumber (I think I may have just created a new label…?), I consulted Rob and just went with this idea for planting. There were already a few holes in the bottom of the planter and because it was from another project I had done previously, there was a hole in the side of it closer to the top. So instead of filling the entire thing with potting soil, I filled the bottom half with sand from Bo’s sandbox, then filled the rest with potting soil.
Sponsored Sponsored

 

pumpkin topiary, crafts, gardening, halloween decorations
STEP 6: Plant flowers/plants. Lastly, I planted my three beautiful mums around my stacked pumpkins. Doing this made my PVC pipe lean a little but once I got all of the mums planted and the soil mashed down, the pumpkins sat up straight and sturdy. *Note: I thought for a split second of doing this project like I did with the pedestal table I created back at the beginning of the summer where I used concrete to set the PVC pipe. However, I didn’t want to spend more money on supplies and I figured this is a seasonal project so I can always take it apart and use it again next year, or take the pumpkins off and stack something else for Christmas or other holidays. Plus, the concrete would make it super difficult to move around to different locations should I want to put it on my other stoop.

 

pumpkin topiary, crafts, gardening, halloween decorations
OPTIONAL STEP: Add lights. I wanted my pumpkin topiary to be seen at night so I added some fairy lights inside each pumpkin. I’m really happy with how this pumpkin topiary came out.

 

pumpkin topiary, crafts, gardening, halloween decorations
As I’ve mentioned in a previous post, we don’t celebrate Halloween in our home, but more harvest/fall season in general; I think, however, this topiary is all fall with a classy touch on Halloween.
Loading...